Cut to 0.1mm accuracy18mm boards ready in 1–5 working daysFree delivery over £1,000 within 35 miles
Mon–Fri 8am–5pm07791 290848Trade customers
Popular:
.
.

Edgebanding Explained: 0.8mm, 1mm or 2mm Edging?

Edgebanding seals and finishes the raw edges of a cut panel. It protects the core from moisture and knocks, and gives furniture a clean, professional look. Here is how to choose the right edging for each part of your project.

Our edgebanding machine in Fengate
Our edgebanding machine in Fengate

What is edgebanding?

Edgebanding is a thin strip of material, usually ABS, applied to the cut edge of a board with hot-melt adhesive on an edgebanding machine. The machine then trims it flush and finishes the corners, so the edge looks like part of the panel. Most decors are available with matching edging.

Which thickness should I choose?

Thickness Typical use
0.4mm – 0.8mm Hidden or low-wear edges: carcass backs, top and bottom edges inside cabinets
1mm A good all-round choice for carcass front edges and shelves
2mm High-wear and on-show edges: doors, drawer fronts, worktop-style edges, anything that gets knocked

A popular combination for kitchens and wardrobes is 2mm on doors and drawer fronts and 1mm on carcass front edges and shelves.

Which edges should I band?

As a rule, band every edge you will see or touch. Edges that sit against a wall, inside a joint or behind a back panel can usually be left raw. We use a simple code to describe each edge:

  • L1 and L2 – the two long edges.
  • W1 and W2 – the two short edges.

Examples:

  • Cabinet side: front edge only (L1).
  • Shelf: front edge only (L1), or all four if it is a free-standing shelf.
  • Door or drawer front: all four edges (L1, L2, W1, W2).

Matching or contrasting edging?

Matching edging blends the edge into the face for a seamless look. Contrasting edging – a black edge on white, for example, or an oak edge on a plain colour – can be a striking design feature. Just tell us which decor you want on each edge.

ABS or real wood veneer edging?

  • ABS edging is a tough plastic edging made to match each board’s colour and pattern. It is impact-resistant, does not chip like melamine edging and is the standard choice for MFC and lacquered MDF.
  • Real wood veneer edging is a thin strip of genuine timber, used on veneered boards and plywood so the edge matches the real wood face. It can be sanded and oiled or lacquered with the face.

Painted MDF does not normally need edging at all – the edges are sealed and painted with the face. See MDF cut to size.

Why we use PUR glue

Most edging is applied with hot-melt EVA glue. We use PUR (polyurethane) glue, which cures into a much stronger, more heat- and water-resistant bond with a thinner glue line. That matters on kitchen doors near kettles and dishwashers, bathroom furniture and anything that is wiped down often – the edge is far less likely to lift or show a dark line.

Edging thick and shaped panels

18mm boards take standard-width edging. Thicker panels, such as 36mm doubled-up worktop-style shelves and end panels, need wider tape – tell us the finished thickness on your cutting list. Curved and shaped parts cut on our CNC can be edged too; send us a drawing and we will confirm.

A quick way to choose

Part Suggested edging
Kitchen and wardrobe doors, drawer fronts 2mm on all four edges
Carcass front edges, shelf fronts 1mm, or 2mm for a heavier-duty look
Edges hidden against walls or other panels None, or 0.4–0.8mm to seal
Edges near sinks, kettles and dishwashers Banded with PUR glue, even if hidden
Birch plywood with a feature edge Leave unbanded, sand and lacquer

Don’t forget the extra thickness

Edging adds thickness to the panel. Tell us whether your sizes are finished sizes (including edging) or cut sizes – our cutting list guide explains how.

Get your panels edged in Peterborough

We cut and edge in-house, usually within 1–5 working days for standard 18mm boards (ask us about thicker boards). Find out more about our edgebanding service, or call 07791 290848, WhatsApp 07791 290848 or email info@cutandedgexpress.co.uk.

Edging thickness: common questions

Is 1mm or 2mm edging better?

2mm is tougher and gives a slightly rounded, more solid-looking edge, so it is best on doors and drawer fronts. 1mm is neat and economical on carcass edges and shelves.

Can you match the edging to my decor?

Yes – we use edging matched to the board’s colour and pattern. If you want a contrasting edge, tell us which colour.

Do I need to edge the back of a shelf?

Not usually, unless it will be seen or is near water. Banding hidden edges in kitchens and bathrooms helps keep moisture out of the chipboard core.

Related: MFC cut to size · MDF sheets cut to size · UK board sizes · Edgebanding service

WhatsApp us